Model 110-T

Liên hệ

Giá 1.000₫

Model 110-T Mounts at the end of a rotating axis. Mount by the press fit receptacle accessory. Wires attach using the accessory receptacle and cap. Mercotac models 110-T & 105 are ideal for shaft grounding applications, including HVAC and VFD motor shaft grounding, thus avoiding very costly bearing damage. Model No. Terminals Voltage AC/DC Amp Rating @240VAC Max. Freq. MHz Contact Resistance Max. RPM Temp Max. F (C) / Min. F (C) Rotation Torque (gm-cm) Circuit Separation 110-T 1 N/A 10 200 <1m 3600 140 (60) /-20(-29) 35 N/A 110-TS 1 N/A 10 200 <1m 3600 140 (60) /-20(-29) 35 N/A 110-TL 1 N/A 10 200 <1m 1200 140 (60) /-20(-29) 10 N/A 105 * 1 N/A 4 200 <1m 7500 212 (100) /45(7) <10 N/A 105-SS * 1 N/A 4 200 <1m 7500 212 (100) /45(7) <10 N/A "T" designator indicates standard model "TS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments) "TL" designator indicates low torque "SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments) * indicates high temp....

Thông tin sản phẩm
Tài liệu tải về
Đặt hàng
Báo giá

Model 110-T


	Mounts at the end of a rotating axis. Mount by the press fit receptacle accessory. Wires attach using the accessory receptacle and cap.

Mercotac models 110-T & 105 are ideal for shaft grounding applications, including HVAC and VFD motor shaft grounding, thus avoiding very costly bearing damage.


Model No.	Terminals	Voltage AC/DC	Amp Rating @240VAC	Max. Freq. MHz	Contact Resistance	Max. RPM	Temp Max. F (C) / Min. F (C)	Rotation Torque (gm-cm)	Circuit Separation

110-T

N/A

200

<1m

3600

140 (60) /-20(-29)

N/A

110-TS

N/A

200

<1m

3600

140 (60) /-20(-29)

N/A

110-TL

N/A

200

<1m

1200

140 (60) /-20(-29)

N/A

105 *

N/A

200

<1m

7500

212 (100) /45(7)

<10

N/A

105-SS *

N/A

200

<1m

7500

212 (100) /45(7)

<10

N/A

"T" designator indicates standard model
"TS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)
"TL" designator indicates low torque
"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)
* indicates high temp. high RPM
Note: The anodized aluminum housing of the 110 & 105series Mercotac is electrically "hot" to the internal conductor.

Model 110-T & 105 Accessories

5920
one contact receptacle

5921-S
one contact receptacle
w/ 6" wire

5952
one contact cap
w/solder lug

Receptacle used for mounting to rotating device.
Accessories are required for wire connections. Order Separately.

Model 110-T & 105 Connections


Note: The metal receptacle used for mounting is electrically conductive. Therefore, if desired, it can be used as the electrical connection between the 110 and the rotating member of the machine using Part #5920. However, if an insulated mounting at the rotating member is being used, then Part #5921-S with six inch wire lead is used for the electrical connection.

Model 110-T & 105 Suggested Mounting Methods

Model 110-T is typically mounted by the knurled metal receptacle, which is press-fit into the rotating member of the machine When mounting horizontally, mount the Mercotac so the body of the connector rotates.

Receptacle Mount Hole Dimensions
MODEL		HOLE DIAMETER (Ø) *	DEPTH
5920, 5921-S		.283" (7.19)	.35" (8.89)
*Inch (mm) Tolerance Ø	+.001" (+.025)
	-.000" (-.000)

Installation Notes:

the up arrow should not point below horizontal
do not solder to or bend connector tabs
avoid lateral forces and mechanical loads (overly stiff or tight wires)
do not rigid mount both ends of connector
limit mounting eccentricity (runout / wobble) to .005" (.13mm)
provide overload protection within the circuit
avoid vibration and bumping motions

Test