Model 110

Còn hàng

Giá 1.000₫

Model 110 Model 110 One Conductor, 10 Amp Mounts at the end of a rotating axis. Mount by the press fit receptacle accessory. Wire attaches using the accessory receptacle or cap. This model is designed to mount at the bottom of a vertical rotating shaft. Model No. Terminals Voltage AC/DC Amp Rating @240VAC Max. Freq. MHz Contact Resistance Max. RPM Temp Max. F (C) / Min. F (C) Rotation Torque (gm-cm) Circuit Separation 110 1 N/A 10 200 <1m 3600 140 (60) /-20(-29) 35 N/A 110-SS 1 N/A 10 200 <1m 3600 140 (60) /-20(-29) 35 N/A 110-L 1 N/A 10 200 <1m 1200 140 (60) /-20(-29) 10 N/A "SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments) "L" designator indicates low torque Note: The anodized aluminum housing of the 110 series Mercotac is electrically "hot" to the internal conductor. Model 110 Accessories 5920 one contact receptacle 5921-S one contact receptacle w/ 6" wire 5952 one contact cap w/solder lug 55337 ring terminal (12-10 AWG) Receptacle used for...

Thông tin sản phẩm
Tài liệu tải về
Đặt hàng
Báo giá

Model 110

Model 110
One Conductor,
10 Amp

Mounts at the end of a rotating axis.
Mount by the press fit receptacle accessory.
Wire attaches using the accessory receptacle or cap.
This model is designed to mount at the bottom of a vertical rotating shaft.


Model No.	Terminals	Voltage AC/DC	Amp Rating @240VAC	Max. Freq. MHz	Contact Resistance	Max. RPM	Temp Max. F (C) / Min. F (C)	Rotation Torque (gm-cm)	Circuit Separation

110

N/A

200

<1m

3600

140 (60) /-20(-29)

N/A

110-SS

N/A

200

<1m

3600

140 (60) /-20(-29)

N/A

110-L

N/A

200

<1m

1200

140 (60) /-20(-29)

N/A

"SS" designator indicates stainless steel ball bearing (recommended for wet or corrosive environments)
"L" designator indicates low torque
Note: The anodized aluminum housing of the 110 series Mercotac is electrically "hot" to the internal conductor.

Model 110 Accessories


5920 one contact receptacle	5921-S one contact receptacle w/ 6" wire	5952 one contact cap w/solder lug

	55337 ring terminal (12-10 AWG)
Receptacle used for mounting to rotating device. Accessories are required for wire connections. Order Separately.

Model 110 Connections


Note: The metal receptacle used for mounting is electrically conductive. Therefore, if desired, it can be used as the electrical connection between the 110 and the rotating member of the machine using Part #5920. However, if an insulated mounting at the rotating member is being used, then Part #5921-S with six inch wire lead is used for the electrical connection.

Model 110 Suggested Mounting Methods

Model 110 is typically mounted by the knurled metal receptacle, which is press-fit into the rotating member of the machine. When mounting horizontally, use the similar model 110-T instead to be able to mount the Mercotac rotary connector so that the body of the connector rotates.

Receptacle Mount Hole Dimensions
MODEL		HOLE DIAMETER (Ø) *	DEPTH
5920, 5921-S		.283" (7.19)	.35" (8.89)
*Inch (mm) Tolerance Ø	+.001" (+.025)
	-.000" (-.000)

Installation Notes:

the up arrow should not point below horizontal
do not solder to or bend connector tabs
avoid lateral forces and mechanical loads (overly stiff or tight wires)
do not rigid mount both ends of connector
limit mounting eccentricity (runout / wobble) to .005" (.13mm)
provide overload protection within the circuit
avoid vibration and bumping motions

Test